| Products --> Laminators --> Quickmount 4 |
| |
| Quikmount 4 - An affordable cold laminator |
| Great for laminating, mounting prints to boards or applying transfer tapes |
 |
|
| |
Provides many features found in
more expensive laminators:
• Heavy duty motor
• Automatic take up shaft
• Shaft for liner paper in front
• Silicone covered rollers
• Rugged steel and aluminum construction |
|
|
 |
|
Quikmount makes laminating easy. Just follow a few simple steps:
1. Insert the hubs into the laminate core (all laminate rolls have
3" cores) |
 |
 |
|
|
|
2. Shafts lift easily out of channels, so laminate rolls can be changed quickly. Collars keep the rolls in place on the shaft. |
|
 |
|
|
|
3. Two pulleys (one is hidden in the photo) and a belt drive the take up shaft |
|
 |
|
|
|
4. Two knobs set the height and pressure of top roller (it is easy to set the pressure properly) Accepts boards up to 1" thick. |
|
 |
|
|
|
5. Pull laminate from the roll, separate the backing paper and tape paper to the core on the take up shaft. |
|
 |
|
|
|
6. Thread the laminate between the two rollers. |
|
 |
|
|
|
| 5. Slide a piece of liner paper between the laminate and bottom roller (to keep the laminate from going down with the roller). |
|
 |
|
|
|
| 8. Run your print through the rollers to apply the laminate. |
|
 |
|
|
|
|
After the print exits out the back, go to the back of the laminator, cut off the laminate, trim and you have a perfectly laminated print. You can then simply run through the next print without going through any more set up since the laminate and liner paper are already threaded through the rollers. |
Stand
Rolling stand is made from steel with four castors. It makes your Quikmount 4 mobile, while saving table space. Silver entry deck is 37" high when placed on stand. |
|
| |
Footswitch
Footswitch provides hands free control. |
|
| Cold LaminatesDaige carries a full line of cold laminates in three finishes: gloss, luster or matte. Gloss is normally used when you need to add glossiness to your finished print. Luster, the most popular finish, is used indoors to eliminate glare and provides a very natural look. Matte is used when you want to tone down the finish. Available in 25", 38", 51" and 54" widths. |
|
|
|
Mounting
Apply mounting adhesive |
| Place a roll of mounting adhesive on the back shaft (for most adhesives you do not need the take up shaft). Run your board through to apply adhesive. It comes out with a release paper covering the adhesive on the board so you can use it at any time. |
|
|
|
Mount prints to boards |
Pull back the first two inches of the release liner covering your board or media to expose the adhesive. Position your print on the board, then rub down the first two inches to the exposed adhesive.
Place the board/print into the Quikmount rollers, drape the print over the top roller (as shown in photo) and run it through the rollers. You get a smooth mount every time. |
|
|
|
| Specifications |
| Roller Widths |
|
25", 38", 55" or 65" |
| Board Thickness |
|
up to 1" thick |
| Speed |
|
8 seconds per foot
(or 7.5 ft. per minute) |
| Electrical |
|
110 volt (U.S.) or
230 volts (for overseas) |
| Outside Dimensions |
25" |
17" W x 31" L |
| 38" |
17" W x 44" L |
| 55" |
17" W x 61" L |
| 65" |
17" W x 71" L |
|
| |
